Key Notes
- Program Shaw Direct remote to TV Using Code: Turn on the TV → Press the TV button→ Enter the 5-digit remote codes → Press the Power button → If the TV turns off, pairing is successful.
- Without Code: Press the TV button → Press 9-9-1 → Press the Channel+ button → Press the OK/Enter button → Press the Power button.
- Program Shaw Direct remote to Set-top box Using Code: Press the SAT button→ Enter the 3-digit remote codes → Press the Power button → If the Set-top turns off, pairing is successful.
- Without Code: Press the SAT button → Press 9-9-1 → Press the Channel+ button → Press the SAT button to save code → Press the Power button.
If you are looking for guidelines to program a Shaw Direct remote to a TV or set-top box, you have come to the right place. With the Shaw Direct remote, you can control any smart TV, Blu-ray/DVD player, audio system, DVR, and so on. However, to use the Shaw Direct remote, you need to program the remote to your TV or other device with the respective remote codes.
In this article, we will teach you how to program the Shaw Direct remote to your TV in simple steps.
How to Program Shaw Direct Remote to TV With Code
If you have the Shaw Direct Remote (IRC 600/URC 600), you can use the below instructions to program the remote to your Samsung TV or any other TV.
[1] Switch on your TV and press and hold the TV button until the AUX and SAT buttons blink 3-4 times.
[2] Now, enter the 5-digit remote codes and press the Power button.
Note: You can check our detailed guide on Shaw Direct TV Remote Codes to find the right remote code for your television.
[3] If your TV turns off, the remote gets paired successfully to your TV.
[4] Now, press the Power button again to turn on the TV.
If it does not turn on, repeat the same steps with a different remote code.
How to Program Shaw Direct Remote to TV Without Code
If the previous method does not work, you can use the following method to program your Shaw remote to your TV.
[1] Turn on your TV and hold the TV button for a few seconds until you see the AUX and SAT buttons flash 3-4 times.
[2] Press 9-9-1, and the TV button will blink two times.
[3] Keep pressing the Channel+ button until your TV turns off. Then, press the OK/Enter button.
[4] Press the Power button to turn on the TV.
[5] Now, press any buttons on the remote and see whether the TV responds to the remote’s commands.
Note: If you own a Fios TV box, you can check our guide to learn how to program a Fios remote to a cable box.
How to Program Shaw Direct Remote to Set-top Box With Code
[1] Press and hold the SAT button, and you will see the AUX and TV buttons flash 3-4 times.
[2] Press the 3-digit remote code and press the Power button to turn off the set-top box.
Note: The Set-top box remote codes are: 000, 001, 002, 003, 004, 005, 006, 007
[3] If your set-top boxes turn off, your remote has been successfully programmed. If not, repeat the same steps with the different code.
How to Program Shaw Direct Remote to Set-top Box Without Code
[1] Press and hold the SAT button for a few seconds until you see the AUX and TV buttons flash 3-4 times.
[2] Press the 9-9-.1 button on the remote
[3] Then, press the Channel+ button continuously until your set-top box turns off.
[4] Once the set-top box turns off, press the SAT button to save the code.
That’s it. The remote programming is completed. Press the Power button to turn on the set-top box.
FAQ
1. Visit the Gateway Remote Manual website to locate the remote code for your TV.
2. Aim the remote at the TV and press and hold the MENU and OK buttons.
3. Release both buttons when the POWER button on the remote flashes twice.
4. Enter the code. If the code is valid, the POWER button will blink twice.
5. Press the POWER button. If the TV turns off, the remote programming is successful. Otherwise, repeat the steps 2-5 with a different code.
If you encounter the paring issue in the Shaw Direct remote, check whether the batteries have sufficient charge. If not, replace the old batteries with the newer ones.
Yes. You can follow the above instructions to program a Shaw Direct remote to an LG TV using code 9-9-1.
